Vehicles
Sections
10 not categorized PORSCHE CAYMAN S SEAT MOUNT PLATECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 GT3 2007-11 (includes uncategorized and accessory items)
BBI9818200001 Bbi autosport Porsche 981 Cayman GT4 streetcup roll bar features 4130 chrome moly steel tubing for excellent strength to weight ratio and addresses issues such as harness angle, seat travel, and engine compartment access. Taking a sensible design approach, the bar mounts to frame structure in the cabin and rear strut towers to provide the strongest mounting points and maximum protection. For superior strength and rigidity, high strength 4130 chrome moly steel tubing was used throughout and all joints are meticulously tig welded by hand. Bolt-in installation is accomplished by using inner diameter tube clamps that are cnc turned and milled for a precise fit. These unique joints eliminate the unsightly through-bo...(choose a part on the right to read more)
$2,395.00
Make a selection RS21 Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire’s contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline’s sealed camber plates incorporate fk motorsports spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Comes as a set of two. Why are rennline’s strut mounts the best ? General FitmentBOXSTER 2005-08CAYMAN 2006-08 911 2005-08 911 GT3 2007-11
$603.90
Make a selection BBI9978200001 The bbi autosport Porsche 996 & 997 streetcup roll bar features a 2-piece design and 4130 chrome moly steel tubing (1.5" x .120" main hoop & 1.5" x 0.95" rear hoops) for excellent strength to weight ratio. Taking a sensible design approach, the 2-piece construction allows the bar to be mounted to the front seat belt mounts and to the rear strut towers (stronger mounting points), and still be compatible with the factory bose subwoofers. Other similar roll bars on the market are not compatible with the subwoofer. For superior strength and rigidity, the bar utilizes "x" braces on both front and rear sections and each joint has been meticulously tig welded by hand. Bolt-in installation is accomplished by usin...(choose a part on the right to read more)
$2,395.00
Make a selection A2126 The girodisc system is a direct replacement for the oe disc on all 997.2 GT3/gt2's, with or without the OEM pccb rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with oe calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your abs efficiency. General Fitment911 TURBO/GT2 2001-05911 GT3 2007-11 911 TURBO/GT2 2010-13
$1,620.00
Make a selection A2032 The girodisc system is a direct replacement for the oe disc on all 997.1 GT3/gt2's, both pccb and non-pccb equipped vehicles. General Fitment911 TURBO/GT2 2001-05911 GT3 2007-11 911 TURBO/GT2 2007-09 911 TURBO/GT2 2010-13 911 2009-12 911 1998-05 911 2005-08
$1,620.00
Make a selection A1126 The girodisc system is a direct replacement for the oe disc on all 997.2 GT3/gt2's, with or without the OEM pccb rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with oe calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your abs efficiency. General Fitment911 TURBO/GT2 2007-09911 GT3 2007-11 911 TURBO/GT2 2010-13
$2,160.00
Make a selection A1127 The girodisc system is a direct replacement for the oe disc on all 997.2 GT3/gt2's, with or without the OEM pccb rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with oe calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your abs efficiency. General Fitment911 TURBO/GT2 2010-13911 GT3 2007-11
$2,160.00
Make a selection FVD512991GT3RS Made in Germany by a premier manufacturer of motorsport body work. Extremely high-quality, aero-tested, paintable grp (glass reinforced plastic) deck lid with functional GT3 wing. The decklid has functional, yet subtle ram air spoiler incorporated into the design like the GT3. The ram air spoiler increases the velocity of the air into the intake for added performance. This decklid is also available with a polished carbon wing, part # FVD 512 991 GT3 rsc features: produced by a premier German motorsports manufacturer. Motorsport quality standards. Lightweight. Decklid made of high strength, lightweight grp (glass reinforced plastic). Mounts like factory. Includes: grp deck lid grp wing grp end plates aluminum up...(choose a part on the right to read more)
$5,362.50
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES99115000S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - net weight is 16.4 kg / 36 lbs. (10 lb savings over stock 3.4 l mufflers) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - 90 db maximum (oem muffler is 75 db for reference). - replaces OEM side mufflers and connects to OEM header and catalytic flange. Please note: this muffler does not include exhaust valves and is meant to replace the OEM system on the base 3.4l 991 (2012+). Power is stated at the crank. This is the very 1st aftermarket muffl...(choose a part on the right to read more)
$3,869.80
Make a selection M500021 The 4-way adjustable motorsport damper has been developed over the last few years in conjunction with many professional racing teams all over the world. After winning the fia European touring car championship (etcc in 2004 with our triple adjustable damper, we designed and developed this unique 4-way damper with andy priaulx's team in preparation of the 2005 fia world touring car championship (wtcc. The rest is history and the 2005, 2006 and 2007 fia wtcc title was clinched by andy priaulx running the moton 4-way damper system. General Fitment911 1984-86911 GT3 2007-11
$13,161.15
Make a selection HEI964001002S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We r...(choose a part on the right to read more)
$694.10
Make a selection RE3204 Securing a 997/996/Boxster or Cayman to a trailer is next to impossible without the use of wheel straps that are just about guaranteed to destroy your wheels in time. Save those expensive wheels with a set of inexpensive tie down hooks from rennline. These hooks have been specifically engineered to bolt to the front of your car without any modification or removal of any factory torque bolts. Another great feature of these hooks are that rennline has incorporated a much needed jack pad that will allow you to easily lift the front of your car without the worry of damaging your rocker panel or plastic under trays. Rennline's rear tie-down brackets are available in 66° to allow you to install these brackets in ma...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08 911 1998-05 911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11
$214.50
Make a selection HEI964001002A Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Retains full seat adjustability. Aluminum finish. Primarily for street use as a harness bar is not an option. Pleas...(choose a part on the right to read more)
$938.30
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |